Nortel 425-24T Скачать руководство пользователя страница 307

Страница: 307 / 488

Chapter 7 System configuration using the CLI

307

System Configuration Guide

The

default lldp port status

command is in the config-if command

mode.

Table 101

describes the parameters and variables for the

default lldp port

status

command.

show lldp command

The

show lldp

command displays configuration data for LLDP. The syntax for

the

show lldp

command is:

show lldp [local-sys-data] [mgmt-sys-data] [stats]

The

show lldp

command is in the exec command mode.

Table 102

describes the parameters and variables for the

show lldp

command.

Table 101

default lldp port status command parameters and variables

Parameters and
variables

Description

port

<portlist>

Specifies the ports affected by the command.

Table 102

show lldp command parameters and variables

Parameters and
variables

Description

local-sys-data

Displays local LLDP system data.

mgmt-sys-data

Displays LLDP management data.

stats

Displays LLDP statistics.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 307 / 488

Результаты поиска

Содержание 425-24T

Отзывы: