manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 331 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 331

Chapter 8 Ethernet port management using the CLI

331

System Configuration Guide

 

default rate-limit command

The

 default rate-limit 

command restores the rate-limiting value for the 

switch to the default setting. The syntax for the 

default

 

rate-limit

 command 

is:

default rate-limit

The

 default rate-limit 

command is in the config-if command mode.

Enabling Custom Autonegotiation Advertisements 
(CANA)

You can control the capabilities that are advertised by the Ethernet switch as part 
of the auto-negotiation process using the Custom Autonegotiation Advertisements 
(CANA) feature. When auto-negotiation is disabled, the hardware is configured 
for a single (fixed) speed and duplex value. When auto-negotiation is enabled, the 
advertisement made by the switch is a constant value based upon all speed and 
duplex modes supported by the hardware. When auto-negotiating, the switch 
selects the highest common operating mode supported between it and its link 
partner.

This section covers:

•

“show auto-negotiation-advertisements command”

•

“show auto-negotiation-capabilities command” on page 332

•

“auto-negotiation-advertisements command” on page 333

•

“no auto-negotiation-advertisements command” on page 334

•

“default auto-negotiation-advertisements command” on page 335

show auto-negotiation-advertisements command

The

 show auto-negotiation-advertisements 

command displays the 

current autonegotiation advertisements. The syntax for the

 show 

auto-negotiation-advertisements 

command is:

show auto-negotiation-advertisements [port <portlist>]

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов