Nortel 425-24T Скачать руководство пользователя страница 447 | Manualshive

Страница: 447 / 488

Nortel 425-24T Скачать руководство пользователя страница 447

447

System Configuration Guide

Appendix E
Command List

This appendix provides the complete CLI command list in alphabetical order,
with approximate page references for the beginning pages of further explanations.

Note:

This information is presented for reference only and should not be

considered to be an exact representation.

Table 168

CLI command list

Command

Page No.

auto-negotiation-advertisements [port <portlist>]
[10-full] [10-half] [100-full] [100-half] [1000-full]
[1000-half] [asymm-pause-frame] [pause-frame]
[none]

auto-negotiation-capabilities

auto-pvid

Configuring VLANs, Spanning Tree, and
MultiLink Trunking for Nortel Ethernet Switches
325 and 425, Software Release 3.6

(320986-A)

autotopology

autosave enable

banner [ custom | static | disabled | <1-15> LINE |
clear ]

blink-leds <off> <stop>

boot [default]

clear logging [nv]

System Monitoring Guide for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320989-A)

clear-stats [port<portlist>]

System Monitoring Guide for Nortel
Ethernet Switches 325 and 425, Software
Release 3.6

(320989-A)

«
...
445
446
447
448
449
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов