Nortel 425-24T Скачать руководство пользователя страница 274

Страница: 274 / 488

274

Chapter 7 System configuration using the CLI

320985-A Rev 01

Figure 101

show sys-info command output

Setting boot parameters

You can reboot the switch or stack and configure BootP. The topics covered in
this section are:

•

“boot command”

•

“ip bootp server command” on page 275

•

“no ip bootp server command” on page 276

•

“default ip bootp server command” on page 276

boot command

The

boot

command performs a soft-boot of the switch or stack. The syntax for

the

boot

command is:

boot [default]

425-48T(config-if)#show sys-info

Operation Mode: Switch

MAC Address: 00-0F-CD-BF-1E-80

Reset Count: 35

Last Reset Type: Management Reset

Power Status: Primary Power

Autotopology: Enabled

Local GBIC Type: (port 49) GBIC is missing

Local GBIC Type: (port 50) GBIC is missing

sysDescr: Ethernet Switch 425-48T

HW:00 FW:3.5.0.2 SW:v3.6.0

Mfg Date: 05122004

Serial #: SACC2600E5

Operational State:Normal

sysObjectID: 1.3.6.1.4.1.45.3.57.1

sysUpTime: 0 days, 00:38:44

sysNtpTime: SNTP not synchronized.

sysServices: 3

sysContact: c

sysName: Ethernet 425-48T

sysLocation:

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 274 / 488

Результаты поиска

Содержание 425-24T

Отзывы: