manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 275 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 275

Chapter 7 System configuration using the CLI

275

System Configuration Guide

 

The 

boot

 command is in the privExec command mode.

Table 75

 describes the parameters and variables for the 

boot

 command.

ip bootp server command

The 

ip

 

bootp server

 

command configures BootP on the current instance of 

the switch or server. The syntax for the 

ip

 

bootp server

 

command is:

ip bootp server {last|needed|disable|always} 

The 

ip

 

bootp server

 

command is in the config command mode.

Table 76

 describes the parameters and variables for the 

ip

 

bootp server

 

command.

Table 75   

boot command parameters and variables

Parameters and 
variables

Description

default

Restores switch or stack to factory-default settings after rebooting. 

Note: 

When you reset to factory defaults, the stack operational mode, 

last reset count, and reason for last reset will not be set to factory 
defaults.

Table 76   

ip bootp server command parameters and variables

Parameters and 
variables

Description

last|needed|disable|
always

Specifies when to use BootP:

•

last—use BootP or the last known address

•

needed—use BootP only when needed

•

disable—never use BootP

•

always—Always use BootP

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов