manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 115 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 115

Chapter 2 Using the console interface

115

System Configuration Guide

 

When a pause frame is received (by either the GBIC port or its link partner), the 
port suspends transmission of frames for a number of slot times specified in the 
control frame or until a pause-release control frame is received. Both devices on 
the link must support this mode when it is selected.

Asymmetric mode

This mode allows the link partner to send flow control pause frames to the GBIC 
port. When a pause frame is received, the receiving port suspends transmission of 
frames for a number of slot times specified in the control frame or until a 
pause-release control frame is received.

In this mode, the GBIC port is disabled from transmitting pause frames to its link 
partner. Use this mode when the GBIC port is connected to a buffered repeater 
device.

You can choose a high speed flow control mode using CLI commands. For more 
information about the commands see 

“Enabling flow control” on page 326

.

Rate Limiting Configuration screen

The Rate Limiting feature allows you to configure the threshold limits for 
broadcast and multicast packets ingressing on a port for a given time interval. The 
Ethernet Switch 325/425 drops any packets received above the threshold value if 
the traffic ingressing on the port exceeds the threshold. The hardware restrictions 
on this platform do not allow you to determine if the traffic from a port is the 
cause of excess broadcast or multicast traffic. Consequently you cannot perform 
port specific actions such as disabling a port. You can generate a trap to detect the 
excess traffic or you can configure the switch to store a message in the system log 
when the traffic on the port exceeds the threshold value. This message in the 
system log conveys that some traffic to the switch will be dropped.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов