Nortel 425-24T Скачать руководство пользователя страница 141

Страница: 141 / 488

Chapter 3 CLI Basics

141

System Configuration Guide

Figure 33

show tech command output (continued)

show stack-info command

The

show stack-info

is specific only to Ethernet Switch 425-24T and

425-48T in stacked mode. This command displays the current stack information,
which includes

unit numbers, GBIC, and software version for all units.

VLAN members

------ ------ ------ ------ ------ ------ ------ ------ ------ ------

Msti Config Id Selector: 0

Msti Region Name: 00:0f:6a:7d:bb:e0

Msti Region Version: 0

Msti Config Digest:

AC:36:17:7F:50:28:3C:D4:B8:38:21:D8:AB:26:DE:62

Port Role State STP Status Oper Status

---- ---------- ---------- ---------- -----------

1 Root Forwarding Enabled Enabled

2 Disabled Discarding Enabled Disabled

3 Disabled Discarding Enabled Disabled

[...]

24 Designated Forwarding Enabled Enabled

25 Disabled Discarding Enabled Disabled

*****Port Interface*****

Status Auto Flow

Port Trunk Admin Oper Link LinkTrap Negotiation Speed Duplex Control

---- ----- ------- ---- ---- -------- ----------- -------- ------ -------

1 Enable Up Up Enabled Enabled 100Mbps Full

2 Enable Down Down Enabled Enabled

3 Enable Down Down Enabled Enabled

[...]

24 Enable Up Up Enabled Enabled 100Mbps Full

25 Enable Down Down Enabled Enabled

*****System Log*****

Type Time Idx Src Message

---- ----------------------------- ---- --- -------

S 00:00:00:00 1 NVR Base Unit changed

S 00:00:00:00 2 NVR #1 Reset initiated through telnet

by IP address: 11.127.249.74, access mode: no security

S 00:00:00:00 3 NVR SMGR event JOIN STACK

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 141 / 488

Результаты поиска

Содержание 425-24T

Отзывы: