manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 114 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 114

114

Chapter 2 Using the console interface

320985-A Rev 01

 

Choosing a high speed flow control mode

The high speed flow control feature allows you to control traffic and avoid 
congestion on the Gigabit full-duplex link. If the receive port buffer becomes full, 
the Ethernet Switch 425-24T issues a flow-control signal to the device at the other 
end of the link to suspend transmission. When the receive buffer is no longer full, 
the switch issues a signal to resume the transmission. You can choose Symmetric 
or Asymmetric flow control mode.

Symmetric mode

This mode allows both the GBIC port and its link partner to send flow control 

pause

 frames to each other.

Autonegotiation

Indicates if the Autonegotiation has been enabled on the port. When enabled, 
the port only advertises support for 1000 Mb/s operation, in full-duplex mode.

Default Value

Enabled

Range

Enabled, Disabled

Speed/Duplex

Displays if a port is configured to support an Ethernet speed of 10 Mb/s or 100 
Mb/s, in half- or full-duplex mode. This field is set (by default) to 1000 Mb/s, 
full-duplex for Gigabit ports only.

Default

100Mbs/Half (when Autonegotiation is Disabled)

Range

10Mbs/Half, 10Mbs/Full, 100Mbs/Half, 100Mbs/Full

Flow Control

Indicates if the switch or unit has been configured to control traffic and avoid 
congestion on the Gigabit MDA port. Two modes are available (see 

“Choosing 

a high speed flow control mode”

,” next, for details about the two modes). The 

Flow Control field cannot be configured unless you set the Autonegotiation field 
value to Disabled.

Default Value

Disabled

Range

Disabled, Symmetric, Asymmetric

Note: 

All fields (except the 

Unit

 field) described in 

Table 18

 are 

read-only fields.

Table 18   

High Speed Flow Control Configuration screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов