manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 113 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 113

Chapter 2 Using the console interface

113

System Configuration Guide

 

Figure 24   

High Speed Flow Control Configuration

Table 18

 describes the 

High Speed Flow Control Configuration

 screen fields.

Table 18   

High Speed Flow Control Configuration screen fields

Field

Description

Unit

Allows you to select the unit number (when stacking is configured) to view or 
configure. To view or configure another unit, type its unit number and press 

Enter

, or press the spacebar to toggle the unit numbers (the system only 

displays a screen for units that are configured with a Gigabit MDA). This field is 
not visible if the switch is operating in the standalone mode.

Port

Displays the port number 

 High Speed Flow Control Configuration

    Port       Autonegotiation      Speed  Duplex       Flow Control

    ----       ---------------      --------------      --------------

     49          Enabled            1000Mbs / Full        Disabled

     50          Enabled            1000Mbs / Full        Disabled

Use space bar to display choices, press <Return> or <Enter> to select choice.

Press Ctrl-R to return to previous menu.  Press Ctrl-C to return to Main Menu.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов