manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 399 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 399

Chapter 12 Configuring the switch using Web-based management

399

System Configuration Guide

 

Requirements for storing and retrieving configuration
parameters on a TFTP server

The following requirements apply when storing and retrieving configuration 
parameters on a TFTP server:

•

The Configuration File feature can only be used to copy standalone switch 
configuration parameters to other standalone switches or to copy stack 
configuration parameters to other stack configurations.

•

For example, you cannot duplicate the configuration parameters of a unit in a 

stack

 configuration and use it to configure a 

standalone

 switch.

•

A configuration file obtained from a standalone switch can only be used to 
configure other standalone switches that have the same firmware revision and 
model type as the donor standalone switch.

•

A configuration file obtained from a stack unit can only be used to configure 
other stacks that have the same number of switches, firmware version, model 
types, and physical IDs as the stack the donor stack unit resides in.

•

Reconfigured stacks are configured according to the unit order number of the 
donor unit. For example, the configuration file parameters from a donor unit 
with physical ID 

x

 are used to reconfigure the unit with physical ID 

x.

•

The configuration file also duplicates any settings that exist for any GBIC that 
is installed in the donor switch.

•

If you use the configuration file to configure another switch that has the same 
GBIC model installed, the configuration file settings will also apply to and 
override the existing GBIC settings.

 

Table 152

 describes the parameters that are not saved to the configuration file.

Table 152   

Parameters not saved to the configuration file

These parameters are not saved:

Used in this screen:

See page:

In-Band Stack IP Address

IP Configuration/Setup

 

385

In-Band Switch IP Address

In-Band Subnet Mask

Default Gateway

Configuration Image Filename

Configuration File Download/Upload

397

TFTP Server IP Address

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов