manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 397 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 397

Chapter 12 Configuring the switch using Web-based management

397

System Configuration Guide

 

Table 150

 describes the items displayed on the 

ASCII Configuration File 

Download 

page.

Storing and retrieving a switch configuration file from a 
TFTP server

You can store switch and stack configuration parameters on a Trivial File Transfer 
Protocol (TFTP) server. You can retrieve the configuration parameters of a 
standalone switch or an entire stack and use the retrieved parameters to 
automatically configure a replacement switch or stack. 

To store a switch or stack configuration, you must set up the file on your TFTP 
server and set the filename read/write permission to enabled.

To download the Ethernet Switch 325/425 configuration file, a properly 
configured TFTP server must be present in your network, and the Ethernet Switch 
325/425

 

must have an IP address. 

To learn how to configure the switch or stack IP address, refer to 

“Configuring 

BootP, IP, and gateway settings” on page 385

.

To store or retrieve a switch or stack configuration file:

1

From the main menu, choose 

Configuration > Configuration File

.

The 

Configuration File Download/Upload

 page opens 

(Figure 164)

.

Table 150   

Ascii Configuration file download page items

Item Description

Ascii Configuration File

Allows you to select the ASCII config file located on 
a personal computer.

Last Manual Configuration 
Status

Displays the status of the download.

Submit

Click on this button to upload the ASCII 
configuration file from the personal computer to the 
Ethernet Switch 325/425.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов