Nortel 425-24T Скачать руководство пользователя страница 256

Страница: 256 / 488

256

Chapter 7 System configuration using the CLI

320985-A Rev 01

Figure 92

show ip command output

show ip address command

The

show ip address

command displays the IP configurations, stack address,

switch address, subnet mask, and gateway address, when the Ethernet Switch
425-24T Switch is in the stack mode. The syntax for the

show ip address

command is:

show ip address [address [stack|switch|unit]]

The

show

ip address

command is in the exec command mode.

Table 62

describes the parameters and variables for the

show ip address

command.

Table 62

show ip address command parameters and variables

Parameters and
variables

Description

address

Displays the current IP address.

stack|switch

Specifies current IP address of the stack or the switch.

unit

Displays the IP address of another unit in a stack.

425-48T(config-if)#show ip

BootP Mode: BootP Disabled

Configured In Use Last BootP

--------------- --------------- ---------------

Stack IP Address: 0.0.0.0 0.0.0.0

Switch IP Address: 192.168.151.175 192.168.151.175 0.0.0.0

Subnet Mask: 255.255.255.0 255.255.255.0 0.0.0.0

Default Gateway: 192.168.151.1 192.168.151.1 0.0.0.0

425-48T(config-if)#

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 256 / 488

Результаты поиска

Содержание 425-24T

Отзывы: