Nortel 425-24T Скачать руководство пользователя страница 301

Страница: 301 / 488

Chapter 7 System configuration using the CLI

301

System Configuration Guide

Table 58

describes the parameters and variables for the

lldp

command.

default lldp command

The

default lldp

command sets the LLDP transmission parameters to their

default values. The syntax for the

default lldp

command is:

default lldp [tx-interval] [tx-hold-multiplier]

[reinit-delay] [tx-delay] [notification-interval]

If no parameters are specified, the

default lldp

command sets all parameters

to their default values.

The

default lldp

command is in the config command mode.

Table 92

describes the parameters and variables for the

default lldp

command.

Table 91

lldp command parameters and variables

Parameters and
variables

Description

tx-interval

<5-327698>

Sets the interval between successive transmission cycles.

tx-hold-multiplier

<2-10>

Sets the multiplier for tx-interval used to compute the Time To Live
value for the TTL TLV.

reinit-delay

<1-10>

Sets the delay for re-initialization attempt if the adminStatus is
disabled.

tx-delay

<1-8192>

Sets the minimum delay between successive LLDP frame
transmissions.

notification-interval

<5-3600>

Sets the interval between successive transmissions of LLDP
notifications.

Table 92

default lldp command parameters and variables

Parameters and
variables

Description

tx-interval

Sets retransmit interval to the default value (30).

tx-hold-multiplier

Sets transmission multiplier to the default value (4).

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 301 / 488

Результаты поиска

Содержание 425-24T

Отзывы: