Nortel 425-24T Скачать руководство пользователя страница 292

Страница: 292 / 488

292

Chapter 7 System configuration using the CLI

320985-A Rev 01

Table 86

describes the parameters and variables for the

sntp server

secondary address

command.

The default is 0.0.0.0.

no sntp server command

The

sntp server

command clears the NTP server IP addresses. The syntax

for the

no sntp server

command is:

no sntp server <primary|secondary>

The

no sntp server

command is in the config command mode.

Table 87

describes the parameters and variables for the

no sntp server

command.

Table 86

sntp server secondary address command parameters and variables

Parameters and
variables

Description

<A.B.C.D>

Enter the IP address of the secondary NTP server.

Table 87

no sntp server command parameters and variables

Parameters and
variables

Description

<primary|secondary>

Enter the NTP server you want to clear:

•

primary—clears the IP address for the primary NTP
server

•

secondary—clears the IP address for the secondary NTP
server

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 292 / 488

Результаты поиска

Содержание 425-24T

Отзывы: