Nortel 425-24T Скачать руководство пользователя страница 224

Страница: 224 / 488

224

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

Figure 82

Console/Comm Port Configuration screen

Note:

Release 3.6 software supports a security enhancement that

provides usernames in addition to passwords for switch access. If you set
a password in the

Console/Comm Port Configuration

screen, the next

time you log in to the switch, you are prompted to enter a valid username
(see

Figure 83 on page 231

). Therefore, ensure you are aware of the

valid usernames (default

and

) before you change passwords.

For information about modifying existing usernames, see

Configuring

and Managing Security for Nortel Ethernet Switches 325 and 425,
Software Release 3.6

(320988-A).

Console/Comm Port Configuration

Comm Port Data Bits: 8 Data Bits

Comm Port Parity: No Parity

Comm Port Stop Bits: 1 Stop Bit

Console Port Speed: [ 9600 Baud ]

Console Switch Password Type: [ None ]

Console Stack Password Type: [ None ]

Telnet/WEB Switch Password Type: [ None ]

Telnet/WEB Stack Password Type: [ None ]

Console Read-Only Switch Password: [ user ]

Console Read-Write Switch Password: [ secure ]

Console Read-Only Stack Password: [ user ]

Console Read-Write Stack Password: [ secure ]

Primary RADIUS Server: [ 0.0.0.0 ]

Secondary RADIUS Server: [ 0.0.0.0 ]

UDP RADIUS Port: [ 1645 ]

RADIUS Shared Secret: [ ]

Use space bar to display choices, press <Return> or <Enter> to select choice.

Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 224 / 488

Результаты поиска

Содержание 425-24T

Отзывы: