manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 323 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 323

Chapter 8 Ethernet port management using the CLI

323

System Configuration Guide

 

Table 110

 describes the parameters and variables for the 

default

 

name

 

command. 

Setting port speed

You can set the speed and duplex mode for a port. This section covers:

•

“speed command”

•

“default speed command” on page 324

•

“duplex command” on page 325

•

“default duplex command” on page 326

speed command

The 

speed

 command sets the speed of the port. The syntax for the 

speed

 

command is:

speed [port 

<

portlist>

] {10|100|1000|auto}

The 

speed

 command is in the config-if command mode.

Table 110   

default name command parameters and variables

Parameters and 
variables

Description

port <portlist>

Specifies the port numbers to clear of names. 

Note:

 If you omit this parameter, the system uses the port number 

you specified in the 

interface

 command.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов