manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 100 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 100

100

Chapter 2 Using the console interface

320985-A Rev 01

 

System Characteristics screen

The 

System Characteristics

 screen (

Figure 19

) allows you to view system 

characteristics and contains three user-configurable fields: 

sysContact

, 

sysName

, 

and 

sysLocation

.

To open the 

System Characteristics

 screen:

➨

Choose 

System Characteristics 

(or press 

s

) from the main menu.

Shutdown

Allows the switch to be safely shut down and powered off. 

This option is followed by two screen prompts that precede the action. At the first 
prompt, enter the time in minutes to wait before the switch is shut down. At the 
second prompt, enter 

Yes

 to confirm the action; or, enter 

No

 to abort the option:

Once the shutdown command is initiated, the switch saves the current 
configuration and can then be safely powered off. If the switch is not powered off 
within the user-specified time period, it is reset. 

Once the shutdown command is initiated, all existing and subsequent Console 
Interface sessions display the following message:

Switch will reset (shutdown) in <xxxx> seconds.

While existing CLI sessions do not receive a warning message, all subsequent 
CLI sessions display the following message:

The shutdown process is in progress. It is safe to 
poweroff the stack. Configuration changes will not be 
saved. Shutdown has blocked the flash. Autoreset in 
<xxxx> seconds.

Neither Web-based management nor Device Manager receive any shutdown 
warning messages.

Command Line 
Interface

Displays the prompt to execute the CLI commands.

Logout

Allows a user in a Telnet session or a user working at a password-protected 
console terminal to terminate the session.

Table 14   

Console interface main menu options (continued)

Option

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов