manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 280 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 280

280

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

Table 80

 describes the parameters and variables for the 

cmd-interface 

command.

Customizing the opening banner

You can customize the banner that appears when you connect to the Ethernet 
Switch 325/425. You can customize the text that reads 

NORTEL

. However you 

cannot customize the second line that reads 

Enter [Ctrl]+y to begin

.

The Banner Control feature provides an option to specify the banner text. If you 
choose not to display the banner, the system enters the command mode through 
the default command interface. You do not have to press the 

Ctrl+y

 keys.

The Banner display that you select is used for subsequent console sessions. For 
executing the new mode in the console, you must logout. For Telnet access, all 
subsequent sessions use the selected mode.

This section covers the following commands:

•

“banner command for displaying banner”

•

“show banner command” on page 281

•

“no banner command” on page 281

banner command for displaying banner

The 

banner

 command for displaying banner specifies the banner displayed at 

startup; either static or custom. The syntax for the 

banner

 command to display 

banner is:

banner [ custom | static | disabled | <1-15> 

LINE

]

Table 80   

cmd-interface command parameters and variables

Parameters and variables

Description

cli | menu

Allows you to set the default management system when 
using console port or Telnet:

•

cli—the system automatically enters the CLI mode 
and displays the CLI prompt after you enter Crtl+Y

•

menu—the system automatically enters the CI menu 
mode and displays the menus after you enter Ctrl+Y.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов