manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 112 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 112

112

Chapter 2 Using the console interface

320985-A Rev 01

 

High Speed Flow Control Configuration screen

The 

High Speed Flow Control Configuration

 screen (

Figure 24

) allows you to 

set the port parameters for the Gigabit Ethernet Interface.

➨

Choose 

High Speed Flow Control Configuration

 (or press 

h

) from the 

Switch Configuration Menu

 screen.

Status

Allows you to disable any of the switch ports. You can also use this field to control 
access to any switch port.

Default Value

Enabled

Range

Enabled, Disabled

Link

A read-only field that indicates the current link state of the corresponding port, as 
follows:

•

Up: The port is connected and operational.

•

Down: The port is not connected or is not operational.

LnkTrap

Allows you to control whether link up/link down traps are sent to the configured trap 
sink from the switch.

Default Value

On

Range

On, Off

Autonegotiation

When enabled, sets the corresponding port speed to match the best service provided 
by the connected station, up to 100 Mb/s in full-duplex mode. This field is disabled for 
all fiber optic ports.

Default Value

Enabled

Range

Enabled, Disabled

Speed/Duplex

Allows you to manually configure any port to support an Ethernet speed of 10 Mb/s 
or 100 Mb/s, in half- or full-duplex mode. This field is set (by default) to 1000 Mb/s, 
full-duplex for Gigabit ports only.

Default Value

10Mbs/Half (when Autonegotiation is Disabled)

Range

10Mbs/Half, 10Mbs/Full, 100Mbs/Half, 100Mbs/Full

Note: 

The GBIC module must be installed to configure the port.

Table 17   

Port Configuration screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов