Nortel 425-24T Скачать руководство пользователя страница 296

Страница: 296 / 488

296

Chapter 7 System configuration using the CLI

320985-A Rev 01

no clock summer-time

The

clock summer-time

command disables the daylight savings time

feature. The syntax for the

no clock summer-time

command is:

no clock summer-time

The

no clock summer-time

command is in the config command mode.

The

no clock time-zone

command has no parameters or variables.

show clock time-zone

The

show clock time-zone

command displays the local time zone settings.

The syntax for the

show clock time-zone

command is:

show clock time-zone

The

show clock time-zone

command is in the config command mode.

The

show clock time-zone

command has no parameters or variables.

Figure 109

displays sample output from the

show clock time-zone

command.

Figure 109

show clock time-zone output

show clock summer-time

The

show

clock summer-time

command displays the daylight savings time

settings. The syntax for the

show clock summer-time

command is:

show clock summer-time

The

show clock summer-time

command is in the config command mode.

425 (config)#show clock time-zone

Time Zone is set to 'PDT', offset from UTC is -08:00

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 296 / 488

Результаты поиска

Содержание 425-24T

Отзывы: