manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 142 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 142

142

Chapter 3 CLI Basics

320985-A Rev 01

 

The syntax for the 

show stack-info

 

command is:

show stack-info

The 

show stack-info

 

command is in the privExec command mode.

The 

show stack-info

 

command has no parameters or variables.

Figure 34

 displays sample output from the 

show stack-info

 

command.

Figure 34   

show stack-info command output

show stacking-mode command

The 

show stacking-mode

 command displays the current and next stacking 

mode for the switch or stack.

The syntax for the 

show stacking-mode

 

command is:

show stacking-mode

The 

show stacking-mode

 

command is in the exec command mode.

The 

show stacking-mode

 

command has no parameters or variables.

425-24T(config)#show stack-info

Unit #  Switch Model      GBIC Port     SW Version

------  ----------------  -----------   ------------

1       425-24T           (1/25) SX     v3.6.0

2       425-24T           (2/25) None   v3.6.0

425-24T(config)#

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов