manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 417 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 417

Installing an SFP Transceiver

417

System Configuration Guide

 

SFP specifications

This section provides technical specifications for the SFP models and includes the 
following topics:

•

“SFP physical specifications”

•

“1000BASE-SX (LC Type) specifications” on page 418

•

“1000BASE-LX (LC Type) specifications” on page 418

•

“1000BASE-SX (MT-RJ Type) specifications” on page 420

SFP physical specifications

This section provides technical specifications for the following SFP models:

Table 158

 describes general specifications for 1000BASE-SX, and 

1000BASE-LX SFPs.

Table 158   

Technical specifications for 

1000BASE-SX, and 1000BASE-LX SFPs

Specification

Description

Dimensions (H x W x D)

0.53 x 0.33 x 2.22 inches(13.4 x 8.5 x 56.4 mm)

Connectors

•

Multimode fiber optic: LC or MT-RJ

•

Single-mode fiber optic: LC or MT-RJ

•

Single-fiber LC fiber optic connector

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов