manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 418 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 418

418

Installing an SFP Transceiver

320985-A Rev 01

 

1000BASE-SX (LC Type) specifications

The Model 1000BASE-SX SFP provides 1000BASE-SX (850 nm, short 
wavelength, Gigabit Ethernet) connectivity using LC duplex multimode fiber 
connectors. The Model 1000BASE-SX SFP supports full-duplex operation only. 

Table 159

 describes standards, connectors, cabling, and distance for the Model 

1000BASE-SX SFP.

1000BASE-LX (LC Type) specifications

The Model 1000BASE-LX SFP provides 1000BASE-LX (1310 nm, long 
wavelength, Gigabit Ethernet) connectivity using LC duplex fiber connectors. The 
long wavelength optical transceivers used in the LX model provide variable 
distance ranges using both multimode and single-mode fiber optic cabling. The 
Model 1000BASE-LX supports full-duplex operation only.

Table 159   

1000BASE-SX SFP specifications

Type

Specification

Standards

Conforms to the following standards:

•

802.3z, 1000BASE-SX

Connectors

Duplex LC fiber optic connector

Cabling

•

62.5 µm MMF optic cable

•

50 µm MMF optic cable

Distance

•

902 ft. (275 m) using 62.5 µm MMF optic 
cable

•

1804 ft. (550 m) using 50 µm MMF optic 
cable

Wavelength

850 nm

Optical budget

7 dB

Laser Transmitter characteristics

Minimum launch power

-10 dBm

Maximum launch power

-4 dBm

Receiver characteristics

Minimum receiver sensitivity -17 dBm

Maximum power input

0 dBm

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов