Nortel 425-24T Скачать руководство пользователя страница 420

Страница: 420 / 488

420

Installing an SFP Transceiver

320985-A Rev 01

1000BASE-SX (MT-RJ Type) specifications

The Model 1000BASE-SX (MT-RJ Type) SFP GBIC provides Gigabit Ethernet
connectivity using MT-RJ multi-mode fiber connectors.

Table 161

describes

standards, connectors, cabling, and distance for the Model 1000BASE-SX
(MT-RJ Type) SFP GBIC.

Table 161

1000BASE-SX SFP specifications

Type

Specification

Standards

Conforms to the following standards:

•

802.3z, Ethernet full duplex

Connectors

Duplex MT-RJ fiber optic connector

Cabling

•

62.5 µm MMF optic cable

•

50 µm MMF optic cable

Distance

•

902 ft. (275 m) using 62.5 µm MMF optic
cable

•

1804 ft. (550 m) using 50 µm MMF optic
cable

Laser Transmitter characteristics

Wavelength

850 nm

Maximum spectral width

0.85 nm

Minimum launch power

-9.5 dB

Maximum launch power

-4.0 dB

Receiver characteristics

Minimum receiver sensitivity -17.0 dBm

Maximum power input

0 dBm

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 420 / 488

Результаты поиска

Содержание 425-24T

Отзывы: