manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 279 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 279

Chapter 7 System configuration using the CLI

279

System Configuration Guide

 

The 

copy tftp config

 

command is in the privExec command mode.

Table 79

 describes the parameters and variables for the 

copy tftp config

 

command. 

Setting the default management interface

You can use 

cmd-interface 

command to set the default management interface 

when you connect to Ethernet Switches 325 and 425 through console port or 
Telnet. This selection is stored in NVRAM and propagated to all units in a stack 
configuration. 

On startup, the switch or stack displays the banner and prompts the user to press 
[Ctrl}+y. After entering these characters, the system displays either a menu or the 
Nortel Command Line Interface (NCLI) prompt, depending on which is set using 
this command.

When using the console port, you must logout for the new mode to display. When 
using Telnet, all subsequent Telnet sessions display the selection. 

cmd-interface command

The 

cmd-interface 

command allows you to set the default management 

interface when you use the console port or Telnet.

The syntax for the 

cmd-interface 

command is:

cmd-interface {cli|menu}

The 

cmd-interface 

command is in the privExec command mode.

Table 79   

copy tftp config command parameters and variables

Parameters and 
variables

Description

address 
<XXX.XXX.XXX.XXX>

Specifies the TFTP server IP address; enter in dotted-decimal 
notation.

 

filename <WORD>

Enter the name of the configuration file you want to copy from 
the TFTP server. 

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов