Freescale Semiconductor MSC8144E Скачать руководство пользователя страница 1040 | Manualshive

Страница: 1040 / 1374

background image

MSC8144E Reference Manual, Rev. 3

20-30

Freescale

Semiconductor

UART

IDLE

12

0

Idle Line Flag
Set when 10 consecutive logic 1s (if M = 0) or 11 consecutive
logic 1s (if M = 1) appear on the receiver input. Once the
IDLE flag is cleared, a valid frame must again set the RDRF
flag before an idle condition can set the IDLE flag.This flag
can generate an interrupt request (refer to Section 20.5).

Clear IDLE by reading IDLE and then reading R[7–0] in the
SCIDR.
Note:

When the receiver wake-up bit (RWU) is set, an idle
line condition does not set the IDLE flag.

1

Receiver input has become
idle.

0

Receiver input is either active
now or has never become
active since the IDLE flag was
last cleared.

OR

11

0

Overrun Flag
Set when software fails to read the SCI data register before
the receive shift register receives the next frame. The OR bit
is set immediately after the stop bit has been completely
received for the second frame. The data in the shift register is
lost, but the data already in the SCI data registers is not
affected. This flag can generate an interrupt request (refer to
Section 20.5).

Clear OR by reading OR then reading R[7–0] in the SCIDR.

1

Overrun.

0

No overrun.

NF

10

0

Noise Flag
Set when the SCI detects noise on the receiver input. NF is
set during the same cycle as the RDRF flag but is not set for
an overrun.

Clear NF by reading NF and then reading R[7–0] in the
SCIDR.

1

Noise.

0

No noise.

FE

9

0

Framing Error Flag
Set when a logic 0 is accepted as the stop bit. FE is set
during the same cycle as the RDRF flag but is not set for an
overrun. FE inhibits further data reception until it is cleared.

Clear FE by reading FE and then reading R[7–0] in the
SCIDR.

1

Framing error.

0

No framing error.

PF

8

0

Parity Error Flag
Set when the parity enable bit, PE, is set and the parity of the
received data does not match its parity bit.

Clear PF by reading PF and then reading R[7–0] in the
SCIDR.

1

Parity error.

0

No parity error.

—

7–1

0

Reserved. Write to zero for future compatibility.

RAF

0

0

Receiver Active Flag
Set when the receiver detects a logic 0 during the RT1 time
period of the start bit search.

RAF is cleared when the receiver detects an idle character.

1

Reception in progress.

0

No reception in progress.

Table 20-11. SCISR Bit Descriptions (Continued)

Name

Reset

Description

Settings

«
...
1038
1039
1040
1041
1042
...
»

Содержание MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8144E

Бренд: 3xLogic Страницы: 2

Бренд: Data Translation Страницы: 60

Бренд: Pima Страницы: 4

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: Moxa Technologies Страницы: 19

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

PISO-725 Series

Бренд: ICP DAS USA Страницы: 8

IPAM-1600s Series

Бренд: C-Com Страницы: 148

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

CNPS7000C Series

Бренд: ZALMAN Страницы: 8

Zypad WL15 Series

Бренд: Eurotech Страницы: 2

Бренд: 3Com Страницы: 53

Бренд: Bailey Страницы: 33

netHOST NHST-T100

Бренд: hilscher Страницы: 75

Бренд: Renesas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды