Freescale Semiconductor MSC8144E Скачать руководство пользователя страница 55

Страница: 55 / 1374

Features

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

1-7

ATM

Controller

Universal test and operations PHY interface for ATM (UTOPIA) controller:
•

UTOPIA level II supports 8/16 bits 25/50 MHz.

•

UTOPIA target mode.

•

Cell-level handshake.

•

Multiple-PHY polling mode.

•

ATM adaptation layers support AAL0, AAL2, and AAL5 protocols in hardware.

•

Full duplex segmentation and reassembly at up to 622 Mbps for AAL5.

•

Full duplex segmentation and reassembly at up to 155 Mbps for AAL2.

•

Up to 255 active VCs internally and up to 64 K VCs using external memory.

•

Unassign cells screening option.

•

Internal rate transmit mode.

•

User-defined cells up to 65 bytes.

•

Separate TxBD and RxBD tables for each virtual channel (VC).

•

Special mode of global free buffer pools for dynamic and efficient memory allocation with early
packet discard (EPD) support.

•

Interrupt report per channel using four priority interrupt queues.

•

Compliant with ATMF UNI 4.0 and ITU specification.

•

ATM pace control (APC) unit.

•

Receive address look-up mechanism.

•

Operations and maintenance (OAM) cell.

•

ATM layer statistic gathering on a per PHY basis.

Serial Peripheral

Interface (SPI)

•

Four-signal interface (SPIMOSI, SPIMISO, SPICLK and SPISEL)

•

Full-duplex operation

•

Works with 32-bit data characters, or with a range from 4-bit to 16-bit data characters

•

Supports back-to-back character transmission and reception

•

Supports master or slave SPI mode

•

Supports multiple-master environment

•

Continuous transfer mode for automatic scanning of a peripheral

•

Maximum clock rate is QUICC Engine clk /8 in master mode and QUICC Engine clk /4 in slave
mode (not in back to back operation)

•

Independent programmable baud rate generator

•

Programmable clock phase and polarity

•

Local loopback capability for testing

•

Open-drain outputs support multimaster configuration

•

Programmable clock gap between two characters in master mode

•

Controlled by the QUICC Engine RISC according to user configuration.

PCI

•

Designed to be compliant with the PCI specification revision 2.2 per the voltage specifications in
the MSC8144E Technical Data sheet.

•

33 MHz and 66 MHz.

•

32-bit PCI interface.

•

PCI 3.3-V compatible.

•

Accesses to all PCI address spaces.

•

PCI-to-system and system-to-PCI streaming.

SRIO Subsystem

•

One serial RapidIO port 1x/4x.

•

RapidIO messaging unit.

Serial RapidIO

Port

(SRIO)

1x/4x serial RapidIO endpoint complies with the following parts of Specification 1.2 of the RapidIO
trade association interconnect specification:
•

Part I (input/output logical specifications).

•

Part II (message passing logical specification).

•

Part III (common transport specification).

•

Part VI (physical layer 1x/4x LP-serial specification).

•

Part VIII (error management extension specification).

The serial RapidIO port supports read, write, messages, doorbells, and maintenance accesses:
•

Small and large transport information field only.

•

All priorities flow.

Table 1-1. MSC8144E Features (Continued)

Feature

Description

Содержание MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MSC8144E

Отзывы:

Похожие инструкции для MSC8144E

Бренды по названию

Популярные бренды

Freescale Semiconductor MSC8144E, Справочное руководство

Результаты поиска

Содержание MSC8144E

Отзывы:

Похожие инструкции для MSC8144E

Бренды по названию

Популярные бренды