Freescale Semiconductor MSC8144E Скачать руководство пользователя страница 985 | Manualshive

Страница: 985 / 1374

background image

TDM Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

19-49

TDMxRFP defines the TDMx receive frame parameters.

Table 19-13. TDMxRFP Bit Descriptions

Name

Reset

Description

Settings

—

31–24

0

Reserved. Write to zero for future compatibility.

RNCF
23–16

0

Receive Number of Channels in a TDM Frame
Specifies the total number of channels that are received in
the TDM modules. One TDM frame can contain 2–256
channels at a granularity of two.
Notes: 1.

RNCF[8-15] = (number of channels that
received on one active link)

×

(number of

active data links) – 1, the number of active
data links is specified in the RTSAL field.

2.

If RCDBL field is clear, then the minimum
number of channels is limit. The minimum
receive number of channels is 128 / (receive
channel size) + 2. For example, if the channel
size is 4 bits, then the receive TDM frame
should contain at least 34 channels.

Table 19-14 describes the RNCF valid value as a function
of the RTSAL field (Receive and Transmit Sharing and
Active Links). For details, see Section 19.2.5.

0x00

Reserved.

0x01

2 received channels.

0x02

Reserved.

0x03

4 received channels.

0x04

Reserved.

.

.

.

0xFD

254 received channels.

0xFE

Reserved.

0xFF

256 received channels.

Note:

The even values are reserved.

—

15–11

0

Reserved. Write to zero for future compatibility.

RCDBL

10–8

0

Receive Channel Data Bits Latency
Defines the maximum amount of receive channel bits
stored in the TDM local memory before they are
transferred for processing. RCDBL determines the
maximum data latency in the following way: Maximum data
latency= (RCDBL)/RCS

×

(receive frame duration). For

details, see Section 19.2.6.
Notes: 1.

The maximum data latency is the latency at
the worst case when the bus is very loaded.
Typically the latency it much smaller.

2.

RCS is field at RFP register defines the
channel size.

3.

The minimum number of receive channel is
limited if the RCDBL field is clear.The
minimum receive number of channels is
128/(receive channel size) + 2.

000

Maximum 64 channel bits.

001

Maximum 128 channel bits.

010

Maximum 256 channel bits.

011

Maximum 512 channel bits.

100

Maximum 1024 channel bits.

101

Maximum 2048 channel bits.

110

Reserved.

111

Reserved.

—

7–6

0

Reserved. Write to zero for future compatibility.

RCS

5–2

0

Receive Channel Size
Determines the receiver channel size – 1. For details, see
Section 19.2.6.

0000

Reserved.

0001 The receiver channel size is 2 bits.
0010 Reserved.
0011

The receiver channel size is 4 bits.

0100–
0110 Reserved.
0111

Receiver channel size is 8 bits.

1000–
1110 Reserved.
1111

Receiver channel size is 16 bits.

«
...
983
984
985
986
987
...
»

Содержание MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8144E

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: Maxim Страницы: 26

Бренд: ROE Страницы: 41

Бренд: Tektronix Страницы: 178

Бренд: UfiSpace Страницы: 35

Бренд: Point of View Страницы: 13

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: Lanner Страницы: 59

Бренд: Unex Страницы: 27

Бренд: Vista Страницы: 93

Бренд: Freescale Semiconductor Страницы: 124

Бренд: Eneo Страницы: 49

Бренд: Xilinx Страницы: 36

Бренд: Enterasys Страницы: 5

Бренд: Sun Microsystems Страницы: 410

Бренд: ZyXEL Communications Страницы: 114

Бренд: Data-Tronix Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды