Freescale Semiconductor MSC8144E Скачать руководство пользователя страница 871 | Manualshive

Страница: 871 / 1374

background image

Dedicated DMA Controller Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

17-31

DTFLOWLVL

27–26

0

RapidIO Transaction Flow Level
Selects a priority level for the transaction flow.
Note:

The value of this bit only applies to the external
RapidIO interface in bypass mode (DBPATMU = 1).

00 Lowest priority transaction

flow.

01 Medium priority transaction

flow.

10 High priority transaction flow.

11 Reserved.

DPCIORDER

24

0

Select PCI Ordering
When set, selects PCI ordering rules, which elevates write
priority one level above reads.
Note:

This bit is ignored unless DBPATMU is set (1).

0

PCI ordering not used.

1

PCI ordering selected.

DSME

24

0

Destination Stride Mode Enable
Enables/disables destination stride mode. When enabled, you
must set the required stride size and distance in the
Destination Stride Register (DSR) for the specified channel.
Note:

This bit is ignored in basic mode (MR[EFE] is cleared
(0).

0

Stride mode disabled.

1

Stride mode enabled.

DTRANSINT

23–20

0

DMA Destination Transaction Interface
After transferring the last block of data in the last link
descriptor, if MR[EOLSIE] is set, then this bit is set and an
interrupt is generated.
Note:

This bit is ignored unless DBPATMU is set (1) and
the transaction is to the RapidIO interface.

1100

RapidIO interface.

1111

Local access memory.

All other values are reserved.

DWRITETTYPE

19–16

0

DMA Destination Transaction Type
Specifies the destination transaction type.
Note:

Writing a reserved value to this field causes a
programming error to be detected and indicated in
SR[PE] for the specified channel.

RapidIO Interface in ATMU
Bypass mode:

0011

SWRITE for all but last
transaction; NWRITE_R
for last transaction.

0100

NWRITE for all but last
transaction; NWRITE_R
for last transaction.

0101

NWRITE_R.

0111

Maintenance write.

All other values reserved.

Local Address space (even in
non-ATMU bypass mode):

0100

Write.

All other values reserved.

—

15–10

0

Reserved. Write to zero for future compatibility.

EDAD

9–0

0

Extended Destination Address
The value depends on the mode:
• Internal RapidIO transactions: Bits 9–4 are reserved and

bits 3–0 represent the most significant 4 bits of the 36-bit
destination address.

• RapidIO interface: Bits 9–2 represent the target ID and bits

1–0 represent the two most significant bits of the RapidIO
address (33–32).

Note:

This field must be cleared (0) in non-bypass mode.

Table 17-13. DATR Field Descriptions (Continued)

Bits

Reset

Description

Setting

«
...
869
870
871
872
873
...
»

Содержание MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8144E

Pixie-4 Express

Бренд: XIA Страницы: 17

ACC-CX3RDK-CU5640

Бренд: e-con Systems Страницы: 9

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

Бренд: ESD Страницы: 28

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: peplink Страницы: 2

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

Vortex86SX VSX-6100

Бренд: ICOP Technology Страницы: 50

Бренд: Comtrend Corporation Страницы: 4

Бренд: Xilinx Страницы: 29

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

Бренд: 8e6 Technologies Страницы: 94

Бренд: MCT Страницы: 12

Бренд: Telit Wireless Solutions Страницы: 79

Бренд: Hama Страницы: 10

Matrix 6H303-48

Бренд: Enterasys Страницы: 90

Бренд: National Instruments Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды