Dell OptiPlex 760 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 203

background image

Back to Contents Page

Dell™ OptiPlex™ 760 Service Manual

Module Bay

Module Bay

You can install a Dell

™

removable device such as a floppy drive, optical drive, or second hard drive in the module bay. You can also install an airbay (filler blank)

in the bay if you do not plan to install a drive.

Your Dell computer ships with either an optical drive or an airbay (filler blank) installed in the module bay. The airbay is held in the module bay with a security
screw only. You can secure a optical drive in the module bay using two methods:

l

Locking switch (accessed by removing the computer cover)

l

Security screw (packaged separately)

See

Securing a Device in the Module Bay

for more information about securing a device in your computer.

Removing and Installing a Device When Your Computer Is Turned Off

1.

If the module bay contains a device that is locked with the locking switch:

a.

Remove the cover (see

Removing the Computer Cover

)

b.

Lift the module locking switch to the unlocked position.

2.

If the module bay contains an airbay, remove the security screw and pull the airbay out of the module bay and skip to

step 5

.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To prevent damage to devices, place them in a safe, dry place when they are not installed in the computer. Avoid pressing down on

them or placing heavy objects on top of them.

1 module locking switch

«
...
177
178
179
180
181
...
»

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

Toughbook CF-47 Series

Бренд: Panasonic Страницы: 32

ToughBook CF-72 Series

Бренд: Panasonic Страницы: 4

Toughbook CF-18 Series

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 140

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 4

Toughbook CF-47 Series

Бренд: Panasonic Страницы: 16

Бренд: Data General Страницы: 132

Бренд: EUROCOM Страницы: 1

FPMA-MOBILE1800

Бренд: New Star Computer Products Страницы: 4

Literail Workstation 6 Person

Бренд: Jason.L Страницы: 4

Бренд: PRESONUS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды