manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

 

 

8.

Connect the adapter cable to the PS/2 serial port adapter connector (PS2/SERIAL2) on the system board (see 

System Board Components

).  

 

 

 

9.

Replace the computer cover (see 

Replacing the Computer Cover

.  

 

 

 

Removing a PS/2 Serial Port Adapter  

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

2.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

  

3.

Gently lift the release tab on the card retention latch from the inside to pivot the latch open. Pivot the latch until it snaps into the open position.  
 

 

  

4.

Disconnect the PS/2 serial-port cable from the system board (see 

System Board Components

).  

 

 

  

5.

Ease the PS/2 serial-port adapter bracket out of its retention slot.  
 

 

  

6.

If you are removing the adapter permanently, install a filler bracket in the empty card-slot opening.  
 

 

 

7.

Before you close the card retention mechanism, ensure that:  
 

l

 

The tops of all cards and filler brackets are flush with the alignment bar. 

 

l

 

The notch in the top of the card or filler bracket fits around the alignment guide.  

 

 

  

8.

Secure any remaining card(s) by closing the card retention latch and snapping it into place.  
 

 

  

9.

Replace the computer cover (see 

Replacing the Computer Cover

).  

 

Back to Contents Page

 

 

 

 

NOTE: 

See the documentation for the PS/2 serial port adapter for information about the cable connections.

 

NOTE: 

Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets keep dust 

and dirt out of your computer and maintain the airflow that cools your computer.

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

Radio Shack TRS-80 Model 3 Operation And Reference Manual preview
TRS-80 Model 3
Бренд: Radio Shack Страницы: 276
Vector Graphic System 2800 User Manual preview
System 2800
Бренд: Vector Graphic Страницы: 40
Antec ISK 310-150 User Manual preview
ISK 310-150
Бренд: Antec Страницы: 10
Commodore Amiga A4000 User Manual preview
Amiga A4000
Бренд: Commodore Страницы: 31
Life Fitness 320-00-00010-01 Owner'S Manual preview
320-00-00010-01
Бренд: Life Fitness Страницы: 36
Asus BM6330 Specifications preview
BM6330
Бренд: Asus Страницы: 2
Dell OptiPlex 380 Service Manual preview
OptiPlex 380
Бренд: Dell Страницы: 54
Pepperl+Fuchs VisuNet GXP PC-GXP1100-22F Manual preview
VisuNet GXP PC-GXP1100-22F
Бренд: Pepperl+Fuchs Страницы: 54
Gateway 300X User Manual preview
300X
Бренд: Gateway Страницы: 118
IBM x3400 M2 7836 Brochure & Specs preview
x3400 M2 7836
Бренд: IBM Страницы: 2
IBM ThinkCentre 8143 (French) Hardware Manual preview
ThinkCentre 8143
Бренд: IBM Страницы: 34
IBM Aptiva Series Quick Start Manual preview
Aptiva Series
Бренд: IBM Страницы: 2
IBM NetVista X40 (Norwegian) Om Programvaren Manual preview
NetVista X40
Бренд: IBM Страницы: 32
IBM PS/2 95 XP 486 Hardware Maintenance Reference preview
PS/2 95 XP 486
Бренд: IBM Страницы: 59
IBM 8543 Service Manual preview
8543
Бренд: IBM Страницы: 24
IBM Series/1 User Manual preview
Series/1
Бренд: IBM Страницы: 91
IBM ThinkPad T40 Service And Troubleshooting Manual preview
ThinkPad T40
Бренд: IBM Страницы: 108
IBM NetVista A21 (French) Guide Pratique preview
NetVista A21
Бренд: IBM Страницы: 74

Бренды по названию

Популярные бренды

Загрузить еще бренды