manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 107 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 107

Back to Contents Page

  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Cards 

 

 

 

Cards  

 

 

 

 

Your Dell™ computer supports a PS/2 serial port adapter and provides the following connectors for PCI and PCI Express cards:

 

l

 

One low-profile PCI card slot 

 

l

 

One low-profile PCI Express x16 card slot 

 

 

 

PCI Cards 

  

 

 

Installing a PCI Card  

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

2.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

 

3.

Gently lift the release tab on the card retention latch from the inside and pivot the latch open.  
 

  

 

 

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

 

NOTE: 

Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets keep dust and dirt 

out of your computer and maintains the airflow that cools your computer.

 

NOTE: 

Your Dell computer uses only PCI and PCI Express slots. ISA cards are not supported.

 

NOTE: 

For PCI card locations, see 

System Board Components

.

1 

release tab 

2 

card retention latch 

3 

card 

4 

card-edge connector 

5 

card connector 

 

 

 

 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов