Dell OptiPlex 760 Скачать руководство пользователя страница 20

Страница: 20 / 203

13.

If you removed a network adapter card and want to turn on the integrated network adapter:

Enter system setup, select

System Configuration

Integrated NIC

, and change the setting to

Enabled

. (See

Entering System Setup

Connect the network cable to the integrated the back panel of the computer.

Installing a PCI Card in the Riser-Card Cage

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

If applicable, remove the card installed in the SLOT2 connector on the system board.

Remove the riser-card cage:

Check any cables connected to cards through the back panel openings. Disconnect any cables that will not reach the riser-card cage once they

are removed from the computer.

Gently pull on the handle and lift the riser-card cage up and away from the computer.

If you are installing a new card, remove the filler bracket to create an empty card-slot opening.

If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. Grasp
the card by its corners, and ease it out of its connector.

Prepare the new card for installation.

Press the release tab to raise the card-retention latch.

riser-card cage

handle

NOTE:

See the documentation that came with the card for information on configuring the card, making internal connections, or customizing it for

your computer.

WARNING:

Some network adapters automatically start the computer when they are connected to a network. To guard against electrical shock, be

sure to unplug your computer from its electrical outlet before installing any cards.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды