Dell OptiPlex 760 Скачать руководство пользователя страница 112

Страница: 112 / 203

If necessary, disconnect any cables connected to the card.

Press the lever with your thumb until you release the securing tab.

If you are removing a PCI Express x16 card, go to

step 6

If you are removing a DVI card, go to

step 7

While pressing the lever, pull the card up and out of the card connector.

While pressing the lever, pull the removal pull tab up and remove the card out of the card connector.

If you are removing the card permanently, install a filler bracket in the empty card-slot opening.

Before you close the card retention mechanism, ensure that:

The tops of all cards and filler brackets are flush with the alignment bar.

The notch in the top of the card or filler bracket fits around the alignment guide.

10.

Secure any remaining card(s) by closing the card retention latch and snapping it into place.

PCI Express x16 card

lever

securing slot (not all cards)

securing tab

PCI Express x16 card connector

PCI Express x16 DVI-card

lever

securing slot

securing tab

PCI Express x16 card connector

NOTE:

Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets keep dust

and dirt out of your computer and maintain the airflow that cools your computer.

CAUTION:

Do not route card cables over the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause

damage to the equipment.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 112 / 203

Результаты поиска

Содержание OptiPlex 760

Отзывы: