Dell OptiPlex 760 Скачать руководство пользователя страница 38

Страница: 38 / 203

Attach the power and data cables to the floppy drive.

Align the shoulder screws with the screw guides, and slide the drive into the bay until it clicks into place.

Replace the optical drive (see

Optical Drive

Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents.

Replace the computer cover (see

Replacing the Computer Cover

Enter system setup and set the

Diskette Drive

option to enable your new floppy drive (see

System Setup

10.

Verify that your computer works correctly by running the Dell Diagnostics (see

Dell Diagnostics

Media Card Reader

Removing a Media Card Reader

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Remove the optical drive (if one exists) and carefully set it aside (see

Removing an Optical Drive

Pull up on the drive-release latch and slide the media card reader to the back of the computer. Then, lift up to remove the drive from the computer.

1 power cable 2 slot verification number

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.

NOTE:

If you will be operating your computer without an optical drive or a 3.5-inch drive installed, the appropriate drive bay insert must be installed in

place of the drive. Contact Dell if you need a drive bay insert.

NOTE:

Since the following steps do not require the complete removal of the optical drive, it is not necessary to disconnect the cables connecting

the optical drive.

CAUTION:

Do not pull the drive out of the computer by the drive cables. Doing so may cause damage to cables and the cable connectors.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды