Dell OptiPlex 760 Скачать руководство пользователя страница 65

Страница: 65 / 203

—

watt

—

The measurement of electrical power. One W is 1 ampere of current flowing at 1 volt.

WHr

—

watt-hour

—

A unit of measure commonly used to indicate the approximate capacity of a battery. For example, a 66-WHr battery can supply 66 W of

power for 1 hour or 33 W for 2 hours.

wallpaper

—

The background pattern or picture on the Windows desktop. Change your wallpaper through the Windows Control Panel. You can also scan in

your favorite picture and make it wallpaper.

WLAN

—

wireless local area network. A series of interconnected computers that communicate with each other over the air waves using access points or

wireless routers to provide Internet access.

write-protected

—

Files or media that cannot be changed. Use write-protection when you want to protect data from being changed or destroyed. To write-

protect a 3.5-inch floppy disk, slide its write-protect tab to the open position.

WWAN

—

wireless wide area network. A wireless high-speed data network using cellular technology and covering a much larger geographic area than WLAN.

WXGA

—

wide-aspect extended graphics array

—

A video standard for video cards and controllers that supports resolutions up to 1280 x 800.

XGA

—

extended graphics array

—

A video standard for video cards and controllers that supports resolutions up to 1024 x 768.

ZIF

—

zero insertion force

—

A type of socket or connector that allows a computer chip to be installed or removed with no stress applied to either the chip or

its socket.

Zip

—

A popular data compression format. Files that have been compressed with the Zip format are called Zip files and usually have a filename extension

.zip

. A special kind of zipped file is a self-extracting file, which has a filename extension of

.exe

. You can unzip a self-extracting file by double-clicking it.

Zip drive

—

A high-capacity floppy drive developed by Iomega Corporation that uses 3.5-inch removable disks called Zip disks. Zip disks are slightly larger than

regular floppy disks, about twice as thick, and hold up to 100 MB of data.

Back to Contents Page

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды