Dell OptiPlex 760 Скачать руководство пользователя страница 152

Страница: 152 / 203

AC Recovery

Determines how the system responds when AC power is re-applied after a power loss. You can set the AC Recovery to:

Power Off

(default)

Power On

Last State

Auto On Time

Sets time to automatically turn on the computer.

Time is kept in the standard 12-hour format (hours:minutes:seconds).

Change the startup time by typing the values in the time and AM/PM fields.

NOTE:

This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if

Auto Power

is set to

disabled

Low Power Mode

Enables or disables low power mode.

This option is disabled by default.

NOTE:

When low power mode is enabled, the integrated network card is disabled.

Remote Wakeup

Allows the system to power up when a network interface controller receives a wake up signal

. You can set Remote Wakeup to:

Disable

(default)

Enable

Enable with Boot NIC

Suspend Mode

Sets the power management suspend mode to:

(default)

Fan Control

Override

Controls the speed of the system fan.

NOTE:

When enabled, the fan runs at full speed.

Maintenance

Service Tag

Displays the Service Tag of your computer.

Asset Tag

Allows you to create a system asset tag if an asset tag is not already set.

This option is not set by default.

SERR Messages

Controls the SERR Message mechanism.

This option is enabled by default.

Some graphics cards require the SERR Message mechanism be disabled.

Image Server

Lookup Method

Specifies how the ImageServer looksup the server address.

Static IP

DNS

NOTE:

You must set the

Integrated NIC

Enable

with

ImageServer

to set the

Lookup Method

ImageServer IP

Specifies the primary static IP address of the ImageServer with which the client software communicates.

The default IP address is

255.255.255.255

NOTE:

You must set the

Integrated NIC

Enable

with

ImageServer

to set the

ImageServer IP

ImageServer Port

Specifies the primary IP port of the image server with which the client software communicates.

The default IP port is

06910

Client DHCP

Specifies how the client obtains the IP address.

Static IP

DHCP

(default)

Client IP

Specifies the static IP address of the client.

The default IP address is

255.255.255.255

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды