manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 34 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 34

  

 

 

5.

Press the release tabs on the plastic insert and press from behind to remove.  
 

  

 

 

Replacing Drive Inserts  

If you are removing a drive, and need to replace the inserts: 

 

 

1.

Place the plastic insert over the opening and press the insert tab down until the plastic insert snaps into place.  
 

 

  

2.

Slide the metal bracket toward the front of the computer and click into place.  
 

 

  

3.

Replace the computer cover (see 

Replacing the Computer Cover

).  

 

 

 

Optical Drive 

 

 

 

 

 

 

Removing an Optical Drive  

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

2.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

 

1  metal insert 

1  shoulder screws  2  plastic drive insert 

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

WARNING: 

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the computer cover. 

 

NOTE: 

If you will be operating your computer without an optical drive or a 3.5-inch device (floppy drive or media card reader) installed, the appropriate 

drive bay insert must be installed in place of the drive. Contact Dell if you need a drive bay insert. See 

Removing Drive Inserts

.

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов