Dell OptiPlex 760 Скачать руководство пользователя страница 158

Страница: 158 / 203

Clearing Forgotten Passwords

Follow the procedures in

Working on Your Computer

Remove the computer cover.

Locate the 2-pin password jumper (PSWD) on the system board, and remove the jumper to clear the password. See

Password Protection

Replace the computer cover (see

Replacing the Computer Cover

Connect your computer and monitor to electrical outlets, and turn them on.

After the Microsoft

Windows

desktop appears on your computer, shut down your computer.

Turn off the monitor and disconnect it from the electrical outlet.

Disconnect the computer power cable from the electrical outlet, and press the power button to ground the system board.

Open the computer cover.

10.

Locate the 2-pin password jumper on the system board and attach the jumper to reenable the password feature.

11.

Replace the computer cover (see

Replacing the Computer Cover

12.

Connect your computer and devices to electrical outlets, and turn them on.

Jumper

Setting

Description

PSWD

Password features are enabled (default setting).

Password features are disabled.

RTCRST

The real-time clock has not been reset.

The real-time clock is being reset (jumpered temporarily).

jumpered

unjumpered

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

This process erases both the system and administrator passwords.

CAUTION:

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды