Dell OptiPlex 760 Скачать руководство пользователя страница 100

Страница: 100 / 203

Back to Contents Page

Dell™ OptiPlex™ 760 Service Manual

System Fan

System Fan

Removing the System Fan

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Remove the heat sink assembly (see

Removing the Processor

Disconnect the power and data cables from the hard drive.

Disconnect the system fans power cable from the system board.

Pull the retention tab at the base of the fan assembly.

Press the retention tab close to the hard drive assembly.

Slide the system fan towards the back of the computer to remove the system fan assembly from the computer.

Installing the System Fan

To install the system fan follow the removal procedure in the reverse order.

Close the computer cover (see

Replacing the Computer Cover

Back to Contents Page

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

retention tab

system fan power cable

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды