Dell OptiPlex 760 Скачать руководство пользователя страница 144

Страница: 144 / 203

Dell™ OptiPlex™ 760 Service Manual

Notes, Cautions, and Warnings

If you purchased a Dell™ n Series computer, any references in this document to Microsoft

Windows

operating systems are not applicable.

Information in this document is subject to change without notice.

2008-

Reproduction in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo,

OptiPlex

TravelLite

OpenManage,

and

StrikeZone

are trademarks of Dell Inc.;

Intel

and

SpeedStep

are registered trademarks of

Intel Corporation in the U.S and other countries

; Microsoft, Windows, Windows Vista

, and the

Windows Start button

are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries;

Computrace

is a registered trademark of Absolute Software Corp.;

Citrix

is a registered trademarks of Citrix Systems, Inc.

and/or one or more of its subsidiaries, and may be registered in the United States Patent and Trademark Office and in other countries.;

Bluetooth

is a trademark owned by

Bluetooth SIG, Inc. and is used by Dell Inc. under license.;

ENERGY STAR

is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell

Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Models: DCTR, DCNE, DCSM, and DCCY

February 2009 Rev. A01

Back to Contents Page

Small Form Factor Computer

About Your Computer

Inside Your Computer

System Setup

Advanced Features

Troubleshooting

Getting Help

Glossary

Removing and Replacing Parts

Working on Your Computer

Removing the Computer Cover

Chassis Intrusion Switch

Cards

Drives

Heat Sink and Processor

System Fan

I/O Panel

Power Supply

Speakers

Memory

Battery

Replacing the System Board

Replacing the Computer Cover

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

CAUTION:

A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.

WARNING:

A WARNING indicates a potential for property damage, personal injury, or death.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды