Dell OptiPlex 760 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 203

Dell OptiPlex 760 Скачать руководство пользователя страница 66

Back to Contents Page

Memory

Dell™ OptiPlex™ 760 Service Manual

Installing Memory Module (s)

Removing Memory Module (s)

You can increase your computer memory by installing memory modules on the system board.

Your computer supports DDR2 memory. For additional information on the type of memory supported by your computer, see the appropriate specifications for
your system in this book.

DDR2 Memory Overview

l

When installed in pairs, DDR2 memory modules should be of

matched memory size and speed

. If the DDR2 memory modules are not installed in matched

pairs, the computer will continue to operate, but with a slight reduction in performance. See the label on the upper-right or upper-left corner of the
module to determine the module's capacity.

The recommended memory configurations are:

¡

A pair of matched memory modules installed in DIMM connectors 1 and 2

or

¡

A pair of matched memory modules installed in DIMM connectors 1 and 2 and another matched pair installed in DIMM connectors 3 and 4

l

If you install mixed pairs of PC2-5300 (DDR2 667-MHz) and PC2-6400 (DDR2 800-MHz) memory, the modules function at the speed of the slowest

module installed.

l

Be sure to install a single memory module in DIMM connector 1, the connector closest to the processor, before you install modules in any other

connector.

.

NOTE:

Always install DDR2 memory modules in the order indicated on the system board.

CAUTION:

Do not install ECC memory modules.

NOTE:

The Ultra Small Form Factor supports only DIMM connectors 1 and 2.

A matched pair of modules in DIMM connectors 1 and 2 (white securing

clips)

B matched pair of memory modules in DIMM connectors 3 and 4 (black securing

clips)

CAUTION:

If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new

modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new
memory module. Otherwise, your computer may not start properly. You should install your original memory modules in pairs either in DIMM
connectors 1 and 2 or DIMM connectors 3 and 4.

«
...
64
65
66
67
68
...
»

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов