Dell OptiPlex 760 Скачать руководство пользователя страница 21

Страница: 21 / 203

Insert the card firmly into the card connector on the riser-card cage.

Lower the card-retention latch and press it into place, securing the card(s) in the computer.

10.

Replace the riser-card cage:

Align the tabs in the side of the riser-card cage with the slots on the side of the computer, and slide the riser-card cage down into place.

Ensure that the riser cards are fully seated in the connectors on the system board.

11.

Reconnect any cables that you removed in

step 4

12.

Connect any cables that should be attached to the card.

13.

Replace the computer cover (see

Replacing the Computer Cover

), reconnect the computer and devices to electrical outlets, and then turn them on.

14.

If you installed a sound card:

Enter system setup, select

System Configuration

Miscellaneous Devices

, and change the

Audio

setting to

Disabled

(see

Entering System

Setup

release tab

card-retention latch

card

card-edge connector

card connector

riser-card cage

slots

riser cards

system board connectors

CAUTION:

Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly

or cause damage to the equipment.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды