Dell OptiPlex 760 Скачать руководство пользователя страница 78

Страница: 78 / 203

Gently remove the processor from the socket.

Leave the release lever extended in the release position so that the socket is ready for the new processor.

Installing the Processor

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Unpack the new processor, being careful not to touch the underside of the processor.

If the release lever on the socket is not fully extended, move it to that position.

Orient the front and rear alignment-notches on the processor with the front and rear alignment-notches on the socket.

Align the pin-1 corners of the processor and socket.

1 center cover latch 2 processor cover 3 processor

4 socket

5 release lever

CAUTION:

Ground yourself by touching an unpainted metal surface on the back of the computer.

CAUTION:

When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket.

NOTE:

You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on

the computer.

1 processor cover

2 tab

3 processor

4 processor socket

5 center cover latch

6 release lever

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 78 / 203

Результаты поиска

Содержание OptiPlex 760

Отзывы: