manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию

Характеристики Dell OptiPlex 760 доступны для скачивания бесплатно на manualshive.com. Здесь вы сможете получить подробное руководство пользователя с описанием всех функций и характеристик этого продукта. Узнайте больше о вашем устройстве, загрузив руководство на manualshive.com.

Поделиться
Скачать
background image

Back to Contents Page

  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Power Supply 

 

 

 

Power Supply  

 

 

Replacing the Power Supply 

 

 

 

 

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

2.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

  

3.

Disconnect the DC power cables from the system board and the drives.  
 

Note the routing of the DC power cables underneath the tabs in the computer chassis as you remove them from the system board and drives. You must 
route these cables properly when you replace them to prevent them from being pinched or crimped. 

 

 

4.

Remove the two screws that attach the power supply to the back of the computer chassis.  
 

 

  

5.

Remove the optical drive and carefully set it aside (see 

Optical Drive

).  

 

 

  

6.

Press the release button located on the floor of the computer chassis and then slide the power supply towards the front of the computer chassis.  
 

  

 

 

7.

Lift the power supply up and out of the computer.  
 

 

  

8.

Slide the replacement power supply into place.  
 

 

  

9.

Replace the screws that secure the power supply to the back of the computer chassis.  
 

 

  

10.

Reconnect the DC power cables.  
 

 

  

11.

Replace the optical drive (see 

Optical Drive

).  

 

 

  

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

1  release button  2  power supply 

3  screws (2)  

4  AC power connector 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

IBM Personal Computer Referencia Rápida preview
Personal Computer
Бренд: IBM Страницы: 64
Balt Wind-Surfer 44162 Assembly Instructions preview
Wind-Surfer 44162
Бренд: Balt Страницы: 4
J.Burrows TORO WORKSTATION JBTORO15WS Assembly Instructions Manual preview
TORO WORKSTATION JBTORO15WS
Бренд: J.Burrows Страницы: 8
Avid Technology Dell T7600 Configuration Manuallines preview
Dell T7600
Бренд: Avid Technology Страницы: 23
Oceanic Veo 180Nx Operating Manual preview
Veo 180Nx
Бренд: Oceanic Страницы: 80
Gateway 5694 - GT - 4 GB RAM Reference Manual preview
5694 - GT - 4 GB RAM
Бренд: Gateway Страницы: 126
Arista ARP-3800AP-E01 Series User Manual preview
ARP-3800AP-E01 Series
Бренд: Arista Страницы: 54
Korg iS50 Installation Manual preview
iS50
Бренд: Korg Страницы: 5
Spectravideo MKI Service – Technical Manual preview
MKI
Бренд: Spectravideo Страницы: 134
Sony VAIO VGN-S360 Service And Warranty Information preview
VAIO VGN-S360
Бренд: Sony Страницы: 1
Sony VAIO VGN-S170 CTO Specifications preview
VAIO VGN-S170 CTO
Бренд: Sony Страницы: 1
Sony VAIO VGN-S150 Specifications preview
VAIO VGN-S150
Бренд: Sony Страницы: 1
Sony VAIO VGN-P598E Specifications preview
VAIO VGN-P598E
Бренд: Sony Страницы: 2
Sony VAIO VGN-P588E Specifications preview
VAIO VGN-P588E
Бренд: Sony Страницы: 2
Sony VAIO VGN-S460P Service Manual preview
VAIO VGN-S460P
Бренд: Sony Страницы: 24
Sony VAIO VGN-P530N Specifications preview
VAIO VGN-P530N
Бренд: Sony Страницы: 2
Sony VAIO VGN-P530H Specifications preview
VAIO VGN-P530H
Бренд: Sony Страницы: 2
Sony VAIO VGN-NW360F Quick Start Manual preview
VAIO VGN-NW360F
Бренд: Sony Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды