Dell OptiPlex 760 Скачать руководство пользователя страница 193

Страница: 193 / 203

For instructions, see the documentation that came with your operating system.

13.

Test the hard drive by running the Dell Diagnostics (see

Dell Diagnostics

14.

Install your operating system on the hard drive.

For instructions, see the documentation that came with your operating system.

Removing the Hard-Drive Fan

Follow the instructions in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Remove the hard drive (see

Removing the Hard Drive

Remove the screw that secures the fan release tab to the hard-drive bracket.

Press down on the fan release tab, and then slide the fan towards the front of the computer so that its side tabs are free of the corresponding slots in
the hard drive bracket.

Gently lift to remove the fan from the hard-drive bracket.

Disconnect the fan cable from the FAN_HDD connector on the system board.

Replacing the Hard-Drive Fan

Connect the hard-drive fan cable to the FAN_HDD connector on the system board.

Align the release tab and the four side tabs on the fan with the five corresponding slots on the hard drive bracket.

Slide the release tab beneath the metal housing covering its slot, and then slide the fan towards the back of the computer.

Replace the screw that secures the fan release tab to the hard drive bracket.

Replace the hard drive (see

Installing a Hard Drive

Replace the computer cover (see

Replacing the Computer Cover

1 hard-drive bracket 2 screw

3 fan release tab

4 fan

5 side tab

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды