Dell OptiPlex 760 Скачать руководство пользователя страница 184

Страница: 184 / 203

Back to Contents Page

Dell™ OptiPlex™ 760 Service Manual

Heat Sink and Processor

Heat Sink and Processor

Removing the Processor

Follow the procedures in

Working on Your Computer

Remove the computer cover (see

Removing the Computer Cover

Remove the fan shroud by lifting the fan shroud up and away from the computer.

Remove the heat sink:

Pull the release lever on the retention base away from the heat sink until the heat sink is released.

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

WARNING:

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.

CAUTION:

When replacing the processor, do not touch the underside of the new processor.

CAUTION:

When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket.

1 fan shroud

WARNING:

The heat sink can get extremely hot. Ensure that the heat sink has had sufficient time to cool before you touch it.

Содержание OptiPlex 760












































































































































































































Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды

Dell OptiPlex 760, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 760

Отзывы:

Похожие инструкции для OptiPlex 760

Бренды по названию

Популярные бренды