Dell OptiPlex 760 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 203

background image

Back to Contents Page

System Board

Dell™ OptiPlex™ 760 Service Manual

Removing the System Board

Replacing the System Board

Removing the System Board

1.

Follow the procedures in

Working on Your Computer

.

2.

Remove the computer cover.

3.

Remove any components that restrict access to the system board (optical drive[s], floppy drive, hard drive, hard-drive bracket, I/O panel (as applicable).

4.

Remove the processor and heat sink assembly:

l

Mini tower: see

Heat Sink and Processor

l

Desktop: see

Processor

l

Small form factor: see

Heat Sink and Processor

l

Ultra small form factor: see

Heat Sink and Processor

5.

Disconnect all cables from the system board.

6.

Remove the screws from the system board.

l

Mini tower: see

Mini Tower System Board Screws

l

Desktop: see

Desktop System Board Screws

l

Small form factor: see

Small Form Factor System Board Screws

l

Ultra small form factor: see

Ultra Small Form Factor System Board Screws

7.

Slide the system board assembly toward the front of the computer, and then lift the board up and away.

8.

If you are replacing the system board, place the system board assembly that you just removed next to the replacement system board to ensure it is
identical.

Mini Tower System Board Screws

WARNING:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION:

Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back

of the computer. While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal
components.

NOTE:

If you are using an ultra small form factor computer, you must remove the system board sled and fan (see

Removing the System Fans

).

«
...
143
144
145
146
147
...
»

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OptiPlex 760

Бренд: IBM Страницы: 170

Бренд: IBM Страницы: 257

Бренд: IBM Страницы: 63

Deep Silence 6 Revision B

Бренд: Nanoxia Страницы: 24

Бренд: Technologic Systems Страницы: 38

Бренд: IBASE Technology Страницы: 58

Presario 3500 Series

Бренд: Compaq Страницы: 68

Бренд: MSI Страницы: 100

Бренд: Omnitronic Страницы: 56

Бренд: Kontron Embedded Computers Страницы: 48

Бренд: XtendLan Страницы: 65

621410U - IntelliStation E - Pro 6214

Бренд: IBM Страницы: 176

Бренд: Moxa Technologies Страницы: 17

Thin Client CD8826

Бренд: ClearCube Страницы: 5

Бренд: Shuttle Страницы: 1

Бренд: Shuttle Страницы: 13

Бренд: Ergotron Страницы: 6

Бренд: EVOC Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды