manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 103 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 103

 

 

 

 

  

 

System Board Components  

  

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

 

WARNING: 

To avoid electrical shock, always unplug your computer from the electrical outlet before removing the computer cover. 

 

CAUTION: 

Be careful when opening the computer cover to ensure that you do not accidentally disconnect cables from the system board.

1 

optical drive 

2 

disk drive 

3 

power supply 

4 

optional chassis-intrusion switch 

5 

system board 

6 

heat sink assembly 

7 

hard drive 

 

 

 

 

1 

internal speaker (INT_SPKR) 

2 

processor connector (CPU) 

3 

processor power connector 
(12VPOWER) 

4 

memory module connectors (DIMM_1, DIMM_2, 
DIMM_3, and DIMM_4) 

5 

password jumper (PSWD) 

6 

SATA drive connectors (SATA0 and SATA1) 

7 

front-panel connector 
(FRONTPANEL) 

8 

power connector (POWER) 

9 

SATA drive connectors (SATA2 
and SATA3) 

10  intrusion switch connector (INTRUDER) 

11  internal USB (INT_USB) 

12  service mode disable jumper 

13  RTC reset jumper (RTCRST) 

14  PCI Express x16 connector (SLOT1) 

15  PCI Express x1 connector 

(SLOT4) 

16  PCI connector (SLOT2, SLOT3) 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов