manualshive.com logo in svg

Dell OptiPlex 760, Руководство по обслуживанию, Страница: 197 / 203

Поделиться
Скачать
Dell OptiPlex 760 Скачать руководство пользователя страница 197

Back to Contents Page

  

Dell™ OptiPlex™ 760 Service Manual 

 

  

Power Button 

 

 

 

Power Button  

 

 

 

 

Removing the Power Button 

 

 

1.

Follow the procedures in 

Working on Your Computer

.  

 

 

  

2.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

  

3.

Gently squeeze the tabs securing the power button assembly to the front of the chassis, and pull the assembly away from the front of the chassis.  
 

 

  

4.

Lift the power button up until the alignment tab on the bottom of the power button assembly is free from the chassis, and remove the power button 
from the chassis.  
 

 

 

Replacing the Power Button 

 

 

1.

Align the tab on the bottom of the power button assembly with the corresponding slot in the front of the chassis, and push the tab into the slot.  
 

 

  

2.

Gently squeeze the tabs on the power button and push the button into the chassis until the tabs lock into place.  
 

 

  

3.

Replace the computer cover (see 

Replacing the Computer Cover

).  

 

Back to Contents Page

 

 

 

 

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. 

Содержание OptiPlex 760












































































































































































































Отзывы:

Нет отзывов